For details about error messages, see p. Indicates whether the printer is online or offline. Press this to switch between online and offline. When the lamp is lit, the printer is online, enabling data reception from the host computer.
When the lamp is unlit, the printer is offline, disabling data reception from the host computer. This indicator remains lit while the power is on.
It is unlit when the power is off or while the printer is in the Energy Saver mode. Lights up whenever a printer error occurs. A red light indicates an error has occurred that makes printing impossible; the yellow light indicates a potential error during printing. Blinks when the printer is receiving data from a computer. The Data In indicator is lit if there is data to be printed. This section describes configuration using the display panel on the initial screen. This section explains how to read the display and using the selection key for the initial display.
By installing options, you can improve the printer performance and have an expanded variety of features to use. For the specifications of each option, see p. Components inside the machine become very hot, and can cause a burn if touched. If the cable is unplugged abruptly, it could become damaged.
Damaged plugs or cables can cause an electrical or fire hazard. The machine could break or cause an injury if dropped. There are two types of memory unit: MB and MB. Install the module to the User Account Enhance Unit slot of the controller board. Up to two paper feed units, can be installed on the printer. See p. You can have two of the following types of extension board installed at the same time: IEEE If you slide out the controller board to install the SDRAM module, the user account enhance unit, or the printer hard disk, carefully follow the instruction below to re-install the controller board.
When moving the printer, use the inset grips on both sides, and lift slowly. The printer will break or. Before using the new paper feed unit, you must make settings in the printer driver. D Lift the printer using the inset grips on both sides of the printer. E Align the printer with the two upright pins on the paper feed unit and then lower the printer slowly. When installing two paper feed units, connect the two units first using the same procedure below before connecting the units to the printer.
Doing so may. Before touching the memory unit, ground yourself by touching something metal to discharge any static electricity. Static electricity can damage the memory unit. Before using the new memory unit, Be sure to make settings in the printer driver.
C Grasp the handles and carefully pull out the controller board. D Place the controller board on a flat surface, and then loosen the four screws to remove the cover. I To install other options on the controller board, follow the appropriate installation procedure s , and then screw down the controller board cover.
K Align the controller board with the left and right rails, and then push it carefully in, until it stops. L Fasten the controller board to the printer using the three screws. Be sure to return the provided screwdriver to its original position on the inside of the front cover. If the memory unit is not properly installed, repeat this procedure. If you cannot install it properly even after reinstallation, contact your sales or service representative.
Install the controller board carefully. For details, see p. Before touching the User Account Enhance Unit, ground yourself by touching something metal to discharge any static electricity. Static electricity can damage User Account Enhance Unit. D Grasp the handles, and then pull the controller board carefully out.
E Place the controller board on a flat surface. Loosen the five screws to remove the cover. G Align the notch of User Account Enhance Unit, and then insert it into the controller board, pressing it down until it clicks into place. J Align the controller board with the left and right rails, and then push it carefully in, until it stops. Push in the controller board until it can go no further. K Fasten the controller board to the printer using the three screws.
If the User Account Enhance Unit is not installed properly, reinstall it following this procedure. If you cannot install it properly even after attempt-. Doing so may cause a machine malfunction or a burn. Before using the new hard disk drive, be sure to make the settings in the printer driver. E Place the controller board on a flat surface, and then loosen the four screws to remove the cover. F Be sure to install the hard disk drive unit as shown.
G Use the screws supplied with the hard disk drive to secure the unit to the controller board. H Connect the power cable to the hard disk drive and controller board. I Connect the flat cable to the hard disk drive and the controller board. Connect the blue end of the flat cable to the controller board. J When installing other options on the controller board, do not close the controller board, but go to the steps for installing the option.
L Align the controller board with the left and right rails, and then push it carefully in, until it stops. M Fasten the controller board to the printer using the three screws. When the power is turned on, the hard disk drive will be formatted automatically.
If the hard disk drive is not installed properly, reinstall it following this procedure. If you cannot install it properly even after attempting reinstallation, contact your sales or service representative. Static electricity can damage the A Check the contents of the package for the following:.
B Turn off the power, and then unplug the power cable. C Loosen the two screws and remove the cover of the E Tighten the two screws to secure the interface unit. F Attach the antenna to the card with the label facing down and the uneven side of the antenna facing up. G With the antenna and the indented end toward you, slowly insert the interface card until it stops.
H Hold the antenna cap with the cut off corners towards you and fit it over the card. After finishing installation, you can check the If the When using the printer with the Bluetooth interface unit installed, Bluetooth needs to be installed on the computer.
Before manipulating the Bluetooth interface unit, touch something metal to discharge static electricity. Static electricity thing damage the Bluetooth interface unit. Loosen the two screws and remove the cover of the Bluetooth interface unit installation unit. H Holding the antenna cap with the two cut-off corners toward you, fit the cap over the card.
If the Bluetooth interface unit is not installed properly, reinstall it following this procedure. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. We also use third-party cookies that help us analyze and understand how you use this website.
These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Ricoh Knowledge Base. Safety Data Sheets Search this site by product category and product name to find safety data sheets for North America. Ricoh Service Request App.
End of support of Windows 7 software included on Ricoh products and services. Ricoh developer support. Register your warranty. Service Request App. Technical support and service. Product support For projectors, desktop and HotSpot printers, video conferencing equipment and interactive whiteboards, call the help desk at Consumer digital camera and support Find product downloads, customer care and more.
Secure fax Call the technical support line at High performance printing can be expected. There are three color toners cyan, magenta and yellow, and a black Ricoh SP Cdn toner cartridge as well. There was a more convenient method of the operation. Here you can update Ricoh drivers and other drivers. It is also able to print data residing in cloud storage and upload scanned data to cloud storage. This desktop office solution is more than your average multifunction laser printer. Managers to print destinations that you extremely frustrating.
Dell OptiPlex desktop The OptiPlex flexible desktop solution is designed for advanced performance and efficient col-laboration.
0コメント